Arduino - EVOLA

Arduino There are 40 products.

  • Out of stock

    The Dragino LoRa Shield is a long range transceiver for Arduino based on RFM95W. This LoRa Shield allows one to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity with minimum current consumption.

    24,00 €
  • Out of stock

    This is an Arduino Leonardo board based on the ATmega32U4 with a built-in ethernet controller (Wiznet 5500 controller with RJ45 connector). Optional PoE (Power over Ethernet)

    47,50 €
  • In stock

    This is an Arduino Ethernet Shield based on the Wiznet W5100 ethernet chip. This module allows an Arduino board to connect to the internet with the easy-to-use Arduino ethernet library. This board exposes the Arduino 1.0 pinout (rev 3) and also includes an onboard micro-SD card slot.

    12,00 €
  • in stock

    Genuino Starter Kit is the ultimate educational solution for learning how to use the Genuino platform. It contains a Genuino Uno Rev3 board, a collection of sensors and actuators, and a book that guides the absolute beginners from their very first steps with electronics into the world of interactive and sensing objects. The Genuino Starter Kit is a great...

    95,88 €
  • In stock

    This module let you control four 250VAC - 10A relays with a 5V signal (15-20mA).  Just send a logic TTL Active LOW signal from a microcontroller (Arduino, Raspberry Pi, 8051, AVR, PIC, DSP, ARM, MSP430) to switch the relay on. Inputs are Opto-isolated and there's Indication LED’s for Relay output status.

    4,80 €
  • Out of stock

    Imagine is a french version of the Arduino UNO compatible board. We produce it locally in our workshop in Juvisy, near Paris. It features the FT231X chip, the last UART to TTL converter from FTDI. Evola Imagine use SMD components only to allow a flat surface on the back and an AtMega328P microcontroller burned with Arduino UNO Optiboot bootloader.

    17,50 €
  • In stock

    The Arduino Industrial 101 is a Evaluation board for the Arduino 101 LGA module. Just like the YUN, it integrates an ATmega32U4 and an Atheros AR9331 with WiFi and Linino OS.  Note that Arduino INDUSTRIAL 101 is completely different from Arduino 101.

    48,00 €
  • Out of stock

    Evola USB Infrared Transceiver is an IR remote control emitter / receiver with built-in USB communication based on ATMega32U4 with the Arduino Leonardo bootloader. This board simply connects to a USB port on a computer, and let you capture and study remote control commands.You can view infrared signals on a logic analyzer, capture, play and replay remote...

    21,50 €
  • Out of stock

    The esp8266 WiFi Shield is an Arduino compatible shield for the esp8266 32-bit Soc. It will add an internet connection to your Arduino and also more features with up to 9 GPIOs, UART, ADC and 4Mb programmable Flash. It's a great introduction to the esp8266 WiFi module combined with the easy-to-use Arduino hardware and software. The esp8266 WiFi Shield is...

    14,00 € 17,50 € -20%
    Reduced price!
  • In Stock

    This kit let you build your own Arduino Shield with the components you like. It includes a Prototyping Arduino Shield with Rev3 pinout, four headers and a reset button switch to solder on the board.

    7,20 €
  • In Stock

    The Relay Shield V3 uses four high quality relays and provides NO/NC interfaces to control high voltage / high current sources. This is a nice way to control devices that can't be controlled directly with Arduino’s Digital I/Os. There are status Leds for each relay to monitor the on/off state of each relay. 

    24,00 €
  • Available with different options

    Evola IDO RF 2.4GHz is an Arduino compatible board UNO R3 format, with embedded nRF24L01+ 2.4GHz radio module. This integrated microcontroller and Radio solution allows you to share your sensors informations over the 2.4GHz ISM band at up to 2Mbps air rate. Available in 5V-16MHz and 3.3V-8MHz version. 

    24,90 €