Shields - EVOLA

Shields There are 25 products.

  • Out of stock

    The Dragino LoRa Shield is a long range transceiver for Arduino based on RFM95W. This LoRa Shield allows one to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity with minimum current consumption.

    24,00 €
  • In stock

    This is an Arduino Ethernet Shield based on the Wiznet W5100 ethernet chip. This module allows an Arduino board to connect to the internet with the easy-to-use Arduino ethernet library. This board exposes the Arduino 1.0 pinout (rev 3) and also includes an onboard micro-SD card slot.

    12,00 €
  • In stock

    This module let you control four 250VAC - 10A relays with a 5V signal (15-20mA).  Just send a logic TTL Active LOW signal from a microcontroller (Arduino, Raspberry Pi, 8051, AVR, PIC, DSP, ARM, MSP430) to switch the relay on. Inputs are Opto-isolated and there's Indication LED’s for Relay output status.

    4,80 €
  • Out of stock

    The esp8266 WiFi Shield is an Arduino compatible shield for the esp8266 32-bit Soc. It will add an internet connection to your Arduino and also more features with up to 9 GPIOs, UART, ADC and 4Mb programmable Flash. It's a great introduction to the esp8266 WiFi module combined with the easy-to-use Arduino hardware and software. The esp8266 WiFi Shield is...

    14,00 € 17,50 € -20%
    Reduced price!
  • In Stock

    This kit let you build your own Arduino Shield with the components you like. It includes a Prototyping Arduino Shield with Rev3 pinout, four headers and a reset button switch to solder on the board.

    7,20 €
  • In Stock

    The Relay Shield V3 uses four high quality relays and provides NO/NC interfaces to control high voltage / high current sources. This is a nice way to control devices that can't be controlled directly with Arduino’s Digital I/Os. There are status Leds for each relay to monitor the on/off state of each relay. 

    24,00 €
  • In stock

    This 9 Axes Motion Shield co-developped with Arduino and Bosch is based on the BNO055 absolute orientation sensor. It integrates three 3-axis sensors : a 14-bit accelerometer, a 16-bit gyroscope and a geomagnetic sensor coupled with a a 32-bit microcontroller.

    28,50 €
  • Out of stock

    This is the 3rd revision of the GPRS Shield for Arduino and Imagine, based on the SIM900 module from SIMCOM. This version is now Arduino R3 pinout compatible.

    49,92 €
  • In stock

    Spécialement conçu pour l'éducation, le shield Imagine réunit sur une seule carte les composants, puces et capteurs les plus utilisés en électronique. Tout est intégré pour se concentrer entièrement sur la programmation sans aucun câblage.Evolutif grâce à la zone de prototypage et les capteurs désactivables par commutateur, le shield Imagine permet de...

    15,00 €
  • Out of stock

    Flash an AVR ATMega328 with Arduino bootloader in less than a few seconds. The Zero Insertion Force (ZIF) connector allows you to insert the IC smoothly without bending pins. Just insert this shield on an Arduino or Imagine board programmed with the Arduino ISP sketch and you're good to go!

    13,90 €
  • In stock

    This is a base board for XBee modules (Xbee, RFBee, WifiBee, BluetoothBee) with on-board FT232RL and Grove JST connectors. The board can be powered with a lithium battery or through USB cable. You can use a Wireless charger, Solar Panel or the USB cable to charge the battery.

    12,00 €
  • In stock

    This is a design for a full-featured motor shield that will be able to power many simple to medium-complexity projects.  Motors and Arduino are not included. Kit comes with all parts necessary, unassembled.

    15,96 €