Top sellers

  • Available within 15 days

    The proxmark3 is a powerful Penetration Testing and Research and development RFID tool. It is designed to snoop, listen and emulate everything from Low Frequency (125kHz) to High Frequency (13.56MHz) tags. It can act as a reader, a writer and clone a RFID tag. It can eavesdrop on a transaction between another reader and a tag, analyze a signal to perform...

    269,00 €
  • In stock

    These are single side copper 7x9cm PCB with standard 2.54mm pitch. Bakelite plates are lightweight and easy to break into smaller parts to fit perfectly your electronic project. Pack include: 10x bakelite PCBs 7cmx9cm.

    7,20 €
  • In stock

    This module let you control four 250VAC - 10A relays with a 5V signal (15-20mA).  Just send a logic TTL Active LOW signal from a microcontroller (Arduino, Raspberry Pi, 8051, AVR, PIC, DSP, ARM, MSP430) to switch the relay on. Inputs are Opto-isolated and there's Indication LED’s for Relay output status.

    4,80 €
  • Out of stock

    13.56Mhz RFID tags with NTAG213 chips. This self adhesive tags supports ISO14443A protocol and are fully programmable. Package content: 10x NTAG213 NFC tags.

    4,80 €
  • In stock

    Don’t limit your projects, think big, think MEGA! Genuino Mega 2560 has been designed with bigger and more ambitious projects in mind. The large number of analog and digital pins, together with a larger memory makes it ideal for devices like 3D printers and other demanding applications. 

    39,00 €
  • Out of stock

    This Lipo battery charger board allows to charge and power your project with a stable 5V voltage from a Lithium batterie, a solar panel and/or from USB. No programming is required. Plug it in and it works. The internal charger IC handles all the power flow between the various components.

    11,94 €
  • Out of stock

    This high quality 5V 2.5A micro USB wall wart adaptor outputs a stable 5V without fluctuation: ideal for supplying power to a Raspberry Pi 3 or any 5V USB powered device that require a lot of current.  Cable length: 120cm

    9,60 €
  • Out of stock

    OLED displays are nice to print characters, bitmap images or different shapes like circles and rectangles. They also have a minimal power consumption and are suitable for battery powered applications. This Oled screen uses the SSD1306 chip and is driven with 2 wires I2C. It is compatible with the most of Arduino libraries.

    6,90 €
  • Out of stock

    Acrylic Transparent Case compatible with Arduino Genuino Uno. This kit ready to assemble comes with all necessary Screws, Nuts, Washers and an Installation guide.

    3,00 €
  • In Stock

    If you are curious to check how much current your device draw, this USB current/voltage meter is really handy. Just plug a USB cable from the power source to the IN port and the cable of your device into the OUT port. Voltage, Current, Battery capacity and Charge Time will display on the screen.

    7,20 €
  • In Stock

    This DC motor driver module is based on the popular L298N Dual H bridge IC. It integrates all necessary components to drive 2 DC motors at up to 2A each, with a voltage between 5 and 35V DC or 1 Stepper motor with a microcontroller like Arduino or esp8266. 

    5,94 €
  • Out of stock

    Evola USB Infrared Transceiver is an IR remote control emitter / receiver with built-in USB communication based on ATMega32U4 with the Arduino Leonardo bootloader. This board simply connects to a USB port on a computer, and let you capture and study remote control commands.You can view infrared signals on a logic analyzer, capture, play and replay remote...

    21,50 €